PRODUCTS

NORITZ MULTI-SYSTEM APPLICATIONS

Commercial Noritz water heaters can be used individually or in a Multi-System (2+ units) when used with either a Quick Connect Cord or a multi-unit System Controller.

  • For Multi-Systems for 2 commercial units, use QC-1 (Quick Connect Cord)
  • For Multi-Systems for 2 to 6 commercial units with a Storage Tank,use SC-201-6M (System Controller for up to 6 Units)
  • For up to 12-unit Multi-System, use SC-201-12M (System Controller for up to 12 Units)
  • For up to 24-unit Multi-System, use SC-201-24M (System Controller for up to 24 Units)

 

Click Here for NORITZ MULTI-SYSTEM APPLICATION SHEET

2 NC250-SV-ASME units installed outside using the Quick-Connect system.

2-Unit Quick Connect System

Two Noritz commercial water heaters installed in parallel can provide hot water to fixtures at twice the capacity as compared to when a single unit is used. The Quick Connect Cord (QC-1) is used to link two identical units together in a simple installation. This connection acts as a communication link between the two units and provides the following features:
1) Doubles the output of the system by allowing the secondary unit to fire when the primary unit reaches capacity
2) Rotates the operation of the two units evenly to prevent premature wear on one unit

10 NC380-SV-ASME units installed on the roof of a manufacuturer using the Multi-System Application.

Multi-System Application For Up to 12 or 24 Units

Up to 12 or 24 Noritz commercial water heaters installed in parallel can provide hot water to fixtures at up to 24 times the capacity as compared to when a single unit is used. System Controller models SC-201-6M(-EXT)(-OD, -DVC) are available and can be used to manifold up to 6 identical units together while providing the following features:
1) Increases the output of the system with the ability to add more BTU’s per added unit
2) Rotates the operation evenly within the Multi-System to prevent premature wear on one unit

Multi-System Application with Storage Tank

A hot water storage tank can be used with the system when a specific application requires higher flow capacity with minimum pressure loss. With the proper System Controller model, the system can handle from 2 up to 24 units that would provide recovery heat to the storage tank while controlling the primary pump in the system. The time in which the hot water in the storage tank reaches the required temperature depends on the amount of BTU’s that is applied to the system, which is directly proportional to the number of units installed in the multi-system. Refer to the Noritz Specification Sheets that include data for BTU and flow capacity ratings to properly size for your specific application.

2 NC380-SV-ASME installed to provide recovery heat to the storage tank.


The storage tank connected to the 2 Noritz NC380-SV-ASME units.

 

 

 
     Model No. NC199 Series NCC199 Series NC250 Series NC380-SV-ASME
     Temperature Rise (°F) 70 100 70 100 70 100 70 100
Flow Rate Capacity (GPM) 1-unit 4.8 3.4 5.3 3.7 6.0 4.2 8.9 6.2
2-unit 9.6 6.8 10.6 7.4 12.0 8.4 17.8 12.4
3-unit 14.4 10.2 15.9 11.1 18.0 12.6 26.7 18.6
6-unit 28.8 20.4 31.8 22.2 36.0 25.2 53.4 37.2
9-unit - - 47.7 33.3 43.2 30.6 80.1 55.8
12-unit - - 63.6 44.4 57.6 40.8 106.8 74.4
24-unit - - 127.2 88.8 115.2 81.6 213.6 148.8
 
Flow Rate Capacity (GPH) 1-unit 288 204 318 222 360 252 534 372
2-unit 576 408 636 444 720 504 1068 744
3-unit 864 612 954 666 1080 756 1602 1116
6-unit 1728 1224 1908 1332 2160 1512 3204 2232
9-unit - - 2862 1998 3240 2268 4806 3348
12-unit - - 3816 2664 4320 3024 6408 4464
24-unit - - 7632 5328 8640 6048 12816 892